The fresh chicken manure produced by large-scale egg and chicken farms generally has a moisture content of 70% -80%, high viscosity, and strong water holding capacity. When it is directly fed into the stack or fermentation tank for flipping, it is easy to stick to the surface of the flipping machine teeth in a large area, forming a hard shell as it accumulates. In mild cases, the flipping resistance increases sharply, the oxygen supply to the stack is insufficient, resulting in slow fermentation heating and uneven maturation. In severe cases, the equipment will shut down and trip, and manual cleaning will be necessary, directly delaying the fermentation cycle of the entire organic fertilizer production line. To completely solve the problem of high humidity chicken manure sticking to teeth, it is not enough to rely solely on frequent cleaning of equipment. It is necessary to systematically adjust the raw material pretreatment, equipment structure adaptation, and flipping process specifications.
First, adjust the front-end raw materials to reduce the stickiness of chicken manure from the source. The direct stacking of high humidity chicken manure is the core cause of sticky teeth. In the pretreatment stage, the moisture content of fresh chicken manure should be reduced to within 60% through a solid-liquid separator, and then crushed straw, rice husk, and decomposed organic fertilizer dry materials should be evenly mixed in a ratio of 3:7. The overall carbon nitrogen ratio of the material should be adjusted to the range of 25:1-30:1, and the overall moisture content of the material should be precisely controlled at 55% -60%, achieving a state of "clumping by hand and dispersing by releasing it". After the tempering is completed, it should be statically stacked for 12 hours to allow the dry auxiliary materials to fully absorb the free water in the chicken manure. The material should be loose and not stick to the hands, greatly reducing the probability of sticking teeth during subsequent flipping from the source.
Select specialized models that are suitable for high humidity materials and optimize the design of the flipping teeth structure. The ordinary trough type flipping machine has small tooth spacing and dense arrangement, which makes it easy to get stuck when filled with high humidity chicken manure. Therefore, it is preferred to use a tracked self-propelled flipping machine for handling such materials, equipped with a large pitch and large gap curved polishing spiral flipping roller. The tooth surface is polished with a mirror finish, and the surface is smooth without burrs. After contact with high humidity chicken manure, it is directly thrown away under centrifugal force, making it difficult to adhere and accumulate. At the same time, widen the gap between the flipping teeth to 8-12 centimeters to prevent small wet materials from getting stuck in the gaps and accumulating layer by layer. During operation, it comes with a dynamic scraping effect, and there will be no obvious sticking of teeth even after several hours of normal operation.
Then standardize the flipping operation process to avoid secondary tooth sticking caused by improper operation. In the initial stage of material stacking, a low-speed shallow flipping mode is first used to repeatedly disperse the quenched and tempered material 2-3 times, allowing the surface material to fully breathe and lose water, and then gradually increasing the flipping depth; During daily homework, control the walking speed to no more than 5 meters per minute, avoid speeding and flipping, and prevent materials from being forcefully squeezed and stuck to the tooth surface. After each shift, run the machine empty for 2-3 minutes, and use the centrifugal force of the high-speed operation of the equipment to automatically shake off the remaining small amount of wet material. Simple cleaning of the tooth surface residue is sufficient, without the need for large-scale disassembly and blockage removal.
After adjusting according to this plan, the organic fertilizer production line will basically avoid the problem of large-scale stick tooth entanglement when processing high humidity chicken manure. The continuous operation time of the flipping machine will be increased by more than three times, and there is no need for frequent shutdown and manual cleaning. The entire fermentation cycle will be shortened from 15 days to 7-10 days, and the uniformity of decomposition will be greatly improved, fully meeting the mass production needs of large-scale chicken farm manure resource treatment.
RSS | Website Map | XML
Copyright©2026 Zgfhfsb.com Tai an Hongxin Environmental Protection Sales Co., Ltd All Rights Reserved
Support:FEIXUN.CC